SMD Rework Solution
We are specialist for SMD Rework such as 0402 chip, CSP,BGA and QFP etc.
ND5100:
PDF for Printing
Rework Station:
Accessories:
Related Systems:
Home(Products) > ND5100 Details
The solder bath is a jet flow system, and jet flow time is automatically operated by the controller which it was set up in advance. The reworked parts should be pull up by hand if process was completed.
ND5100 is a reworking system for through hole type board. The machine has the solder bath, and it can be put in of the 26Kg solder. When reworking, ND5100 is required the nozzle of the size suitable for the reworking parts.
Remove and soldering of the parts are same controlled operation on the machine. And operation of the machine is by foot switch. When reworking the parts of under the board, it is possible by lowering the work table.
The position of the reworking parts can be check by the target mark. It is the lighting mark of a cross. The positioning of the nozzle is possible easily by the mark.
The hole on the board can be cleaning by the air hood of ND5100. The air hood is put on the target position, then, the cleaning switch is ON, and operation is start. ND5100 is automatically soldering and air cleaner is started.
ND5100 Rework Center
The solder bath is a jet flow system, and jet flow time is automatically operated by the controller which it was set up in advance. The reworked parts should be pull up by hand if process was completed.
ND5100 is the rework system for through- hole board.
Reworking is by jet flow soldering
The nozzle for reworking can be change, Then all most all SMD rework will be possible.
Lead free soldering is possible.
It has the function which clean the hole on the board after rework.
It is a best seller machine with the actual result for 20years or more.
Operation
ND5100 is a reworking system for through hole type board. The machine has the solder bath, and it can be put in of the 26Kg solder. When reworking, ND5100 is required the nozzle of the size suitable for the reworking parts.
Controller
Remove and soldering of the parts are same controlled operation on the machine. And operation of the machine is by foot switch. When reworking the parts of under the board, it is possible by lowering the work table.
Target Plate
Lighting Target
The position of the reworking parts can be check by the target mark. It is the lighting mark of a cross. The positioning of the nozzle is possible easily by the mark.
Hole Cleaning
The hole on the board can be cleaning by the air hood of ND5100. The air hood is put on the target position, then, the cleaning switch is ON, and operation is start. ND5100 is automatically soldering and air cleaner is started.
Dimension
Specifications
| Item | Specification |
| Solder Bath | 26 Kg max |
| Temperature Range | 200---350 C degrees max |
| Controller Accuracy | ±1C degree |
| Jet Flow | Variable Screw |
| Work Table | 490 x 410mm |
| Table Height Adjust | 20mm max |
| Table Mat | Heat Resisted and Conductivity |
| Target Marking | Bright cross mark |
| Air Cleaner | Hole cleaning |
| Heater | High-density cartridge heater |
| Power | 200V 2.2KVA |
| Dimension | 490W x 655D x 685Hmm 70Kg approx. |
| Air | 0.3Mpa or more |
The specification are subject to change without notice.
The nozzles are made by request of the customer needs.
M.S.Engineering Co.,Ltd.
1-38-15, Okusawa, Setagaya-Ku, Tokyo, 158-0083 Japan. Phone: +81-3-4283-3951 Fax: +81-3-3728-5232
Copyright(C)2007 M.S.Engineering Co.,Ltd. All rights Reserved.
1-38-15, Okusawa, Setagaya-Ku, Tokyo, 158-0083 Japan. Phone: +81-3-4283-3951 Fax: +81-3-3728-5232
Copyright(C)2007 M.S.Engineering Co.,Ltd. All rights Reserved.